Dimensions: Overall - 127mm x 127 x 57mm (5.0” x 5.0”
x 2.25”), Plastic Electrical Box - 102mm x 102mm x 54mm
(4.0” x 4.0” x 2.14”)
Shipping Weight: 1 kg (2.12 lbs.)
Front Panel Material: 14 gauge brushed stainless steel
Connections: Gel-filled butt connectors
The black plastic rough-in box (part # 259576) may be
purchased separately (Example: Mounting boxes to
studs before the walls are finished for flush installation).
Go to www.vikingelectronics.com and click on “Spare
Parts” to order these rough-in boxes.
E
E
-
-
1
1
6
6
0
0
0
0
-
-
3
3
0
0
A
A
(
(
o
o
p
p
t
t
i
i
o
o
n
n
a
a
l
l
E
E
W
W
P
P
a
a
v
v
a
a
i
i
l
l
a
a
b
b
l
l
e
e
)
)
Important: The E-1600-20A will NOT mount to a standard double gang box.
* Note: Peel off paper liner and adhere gasket to the back of the faceplate, centering it over the
four corner mounting holes.
Optional Enhanced Weather Protection (EWP): The optional EWP products feature
sealed trim pots, sealed DIP switches, hand soldered and silicon sealed connections, rub-
ber boots and gaskets, urethane potted circuit boards and gel- filled butt connectors.
Mounting with Plastic Rough-In Box (included): Flush into walls, mounts to side of wall
stud Mounting with Optional VE-5x5: Surface mount to walls, single gang boxes, dou-
ble gang boxes, posts, or to a Viking VE-GNP Gooseneck pedestal (as shown above).
Note: When mounting outside to rough or uneven surfaces (brick, stucco, etc.) apply a
bead of clear silicone caulking around the top edge and sides of faceplate or VE-5x5.
Dimensions: Overall - 127mm x 127 x 57mm (5.0” x 5.0”
x 2.25”), Plastic Electrical Box - 102mm x 102mm x 54mm
(4.0” x 4.0” x 2.14”)
Shipping Weight: 1 kg (2.12 lbs.)
Front Panel Material: 14 gauge brushed stainless steel
Connections: Gel-filled butt connectors
Optional Enhanced Weather Protection (EWP): The optional EWP products feature
sealed trim pots, sealed DIP switches, hand soldered and silicon sealed connections, rub-
ber boots and gaskets, urethane potted circuit boards and gel- filled butt connectors.
Mounting with Plastic Rough-In Box (included): Flush into walls, mounts to side of wall
stud Mounting with Optional VE-5x5: Surface mount to walls, single gang boxes, dou-
ble gang boxes, posts, or to a Viking VE-GNP Gooseneck pedestal (see options below).
Note: When mounting outside to rough or uneven surfaces (brick, stucco, etc.) apply a
bead of clear silicone caulking around the top edge and sides of faceplate or VE-5x5.
** Important: Optional Braille “Push for Help” label should be adhered to the faceplate in ADA applications. Clean surface with isopropyl alco-
hol, peel off backing and press firmly to the front panel in location as shown above.
*** Caution: When warm air comes in contact with cold surfaces, such as outside walls and conduits, it causes condensation. To prevent con-
densation from accumulating inside the E-1600-30A always bring conduit into the bottom of the unit. If this is not possible, drill a 1/4” diameter
hole in the bottom of the black plastic box.
** Caution: When warm air comes in contact with cold surfaces, such as outside walls and
conduits, it causes condensation. To prevent condensation from accumulating inside the E-1600-20A always bring conduit into the bottom of the unit. If
this is not possible, drill a 1/4” diameter hole in the bottom of the black plastic box.
Comments to this Manuals