Viking ES-3 Manual download pdf (Page 5)

E. Facility Codes

F. Entry Point ID Number

G. Relay Activation Time

I. Programming Features Quick Reference

H. Beep Tones

A Wiegand type card reader can be added to the ES-1 entry point for card access control. Twenty-six bit Wiegand

access cards, such as Viking’s model PRX-C, identify themselves with an 8-digit number. The first three digits

are considered the Facility Code and the last five are the card number.

The ES-1 shares the 5 digit entry code memory location for both keypad entry and card entry. In other words, the

5-digit card number is to be programmed as the tenant’s entry code. Unless facility codes are programmed, the

ES-1 will only need to match the 5-digit card number with any programmed entry code to allow access.

For a higher level of security the 3-digit Facility Code should be programmed. Each ES-1 can be programmed to

accept up to 4 different Facility Codes.

Note: If all 4 Facility Code locations are programmed to “000” (factory setting), the ES-1 will disregard the Facility

Code all together, thus making access entry based only on the card number (or keypad entry) match with the

programmed entry code.

Important: 26-bit Wiegand data limits the facility code range from 001 to 255. A facility code larger than 255 will

not be accepted.

When in programming, enter the 3-digit Facility Code of the access cards being used, then “#” and the memory

locations as follows

The relay activation time can be programmed in seconds from 01 - 99. When in programming, enter the time in

seconds + ##3 (00 = 1/2 second, factory set to 5 seconds).

Example: 05 ##3 = a 5 second relay activation time

The ES-1 outputs event data on the LOG BUS each time a card or keypad is used. An ID number can be pro-

grammed in each ES-1 so that the device receiving the LOG BUS data knows which entry point the event came

from. While in programming, enter a single digit ID number (1-9) + ##7.

Example: 6 ##7 = an Entry Point ID number of 6

While programming the ES-1, a double beep will be heard after entering a valid command or memory location. If

an invalid command or number sequence is entered, it will be indicated by a triple beep. If an error is made, review

the instructions and re-program that location. The ES-1 is capable of detecting hardware memory errors and will

output 4 beeps if there is a problem.

Programming Facility Codes Enter Digits + Location

First Facility Code (default = 0000) ………………......................................….......... 3 digits (0-9) + #911

Second Facility Code (default = 0000) …………………..................…...................... 3digits (0-9) + #912

Third Facility Code (default = 0000) ....................................................................... 3digits (0-9) + #913

Forth Facility Code (default = 0000) ........................................................................ 3digits (0-9) + #914

Description Enter Digits + Location

A single Entry Code …………………………………................................................….. 5 digits (0-9) + #001-250

A single one time use entry code ………………….......................................…............. 5 digits (0-9) +

Q#001-250

Continuous bank of entry codes.......................... Enter first code, then #, then first location, then #

Q + last location

Clear one entry code ................................................................................................... no digits + #001-250

Off mode .....................................................................................................................

Normal Mode (factory setting)......................................................................................

Open mode (only use with compatible strikes, see Programming, section C)...........

Touch tone door strike activation .................................................................................

Card plus keypad mode enabled .................................................................................

Card plus keypad mode disabled (factory setting) ......................................................

#41

Entry point ID number (factory set to 1) ....................................................................... 1 digit (00-01) ##7

Relay activation time (in seconds - factory set to 5 seconds) ...................................... 2 digits (00-20) + ##3

facility codes (all factory set to 000) ............................................................................ 3 digits (00-99) + #911-914

Clear all entry codes and return all programming features back to factory settings .... ### (CAUTION: Erases all Programming!)

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Viking ES-3 Manual Page 5

Comments to this Manuals

Related products and manuals for Security door controllers Viking ES-3