Installation
IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC
outlet and the telephone line. It is recommended that a surge protector be installed to protect against such surges.
Caution: When warm air comes in contact with cold surfaces, such as outside walls, it causes condensation. To
help prevent condensation from accumulating inside the W-1000/3000, bring conduit into the bottom of the unit.
If this is not possible, drill a 1/4” diameter hole in the bottom of the plastic rough-in box.
A. Mounting the W-1000 and W-3000
Front View of Optional
VE-5x5 (not included)
2.25”
Condensation
Drain Hole
* 1/8" thick foam gasket (included)
5.14”
5.22”
3.25”
Call
4.0"
Rear View of VE-5x5 (not included)
5.0” Typical
W-3000-EWP
shown with
optional
Viking Model
VE-5X5 Surface
Mount Box
and
VE-GNP
Gooseneck
Pedestal
(4) 0.38” diameter (for gooseneck mounting)
(4) 0.2 x 0.43 slots for double gang box
(2) 0.2 x 0.43 slots for single gang box
(1) .74" dia
3.0” 3.3”
3.0”
2.1”
Wall Stud
Front View of Plastic
Rough-In Box (included)
Wire knock out
(2) Standard flat head dry wall
(sheet rock) screws (not included)
Marine grade 316 stainless steel
push button switch (sealed per IP67)
Push to Call Button
Blue Call Progress/Nightlight LED
(4) 6-32 X 3/4” Marine grade 316 stainless steel,
flat head, 5/64" hexdrive screws (included)
Condensation Drain Hole
Important: The W-1000/3000 will NOT mount to a
standard double gang box.
Note: The plastic rough-in box (part # 259576)
may be purchased separately in advance. Go to
www.vikingelectronics.com and click on “spare parts”.
The optional VE-5x5 Surface Mount Box is
designed to be surface mounted to a single gang
box, double gang box or VE-GNP gooseneck
pedestal (right). For more information on the
VE-5x5 and VE-GNP see DOD# 424.
* Note: Peel off paper liner and
adhere gasket to the back of the
faceplate, centering it over the
four corner mounting holes.
Marine grade 316 stainless
steel faceplate (W-3000 only)
UP
Call
VIKING©
To open the speaker
box, remove the two
screws from the cover.
Mount the back panel to a
wall, a single gang box or
a 4” x 4” junction box with
the arrow pointing up.
Attach the cover to the
base with the two included
screws as shown.
Front View of the
W-2000A / W-2000A-EWP
Internal View of the back panel
W-2000A / W-2000A-EWP
Side View of the
W-2000A / W-2000A-EWP
B. Mounting the W-2000A
The W-2000A and W-2000A-EWP are designed to be surface
mounted to a single gang box (not included), a standard 4” x 4”
electrical junction box (not included), or directly to a wall or flat
sided post.
Note: For outdoor applications apply
a bead of caulk between back panel
and wall.
2
(4 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals