Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries
assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
DOD# 228
ZF303200 Rev A
Printed in the U.S.A.
P
P
r
r
o
o
d
d
u
u
c
c
t
t
S
S
u
u
p
p
p
p
o
o
r
r
t
t
L
L
i
i
n
n
e
e
.
.
.
.
.
.
7
7
1
1
5
5
.
.
3
3
8
8
6
6
.
.
8
8
6
6
6
6
6
6
F
F
a
a
x
x
B
B
a
a
c
c
k
k
L
L
i
i
n
n
e
e
.
.
.
.
.
.
7
7
1
1
5
5
.
.
3
3
8
8
6
6
.
.
4
4
3
3
4
4
5
5
T
T
r
r
o
o
u
u
b
b
l
l
e
e
s
s
h
h
o
o
o
o
t
t
i
i
n
n
g
g
W
W
i
i
r
r
i
i
n
n
g
g
1. When the reader is powered up the LED’s will momentarily light amber, a victory beep (4-quick beeps) is heard and then the LED’s
will light Red.
2. Present the correct card and the reader will beep once and LED’s will momentarily turn off. It is up to the control panel to control
dual LED and have the LED turn green when an enrolled card is presented.
If reader does not recognize the card/tag (no beep, no LED flash) or reader has short read range, please see table below for possible
causes and solutions.
If any of the corrective actions mentioned above don’t work, please disconnect the reader from panel and power it with a separate power
supply or 9V battery and test card functionality. By powering it individually and off the installation most variables that can cause mal-
function are eliminated. If after the reader is powered by a separate power source the failure persist, please contact Viking Electronics
Product Support.
IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC outlet and
the telephone line. It is recommended that a surge protector be installed to protect against such surges.
!
Black
Green
White
(+) (-)
Power
Supply
Connect to Typical Wiegand
Connections on Entry System
Connect to “-/Ground” on Entry System/
Controller and Earth GND
Note: See “Cable Requirements” on page 2.
Keep unused leads from shorting
When using the PROX-3 with any Viking Entry System/Controller, the provided 12V DC 500mA power adapter should be used. Follow
the directions below to prepare the power supply.
(+) Black
(-) Black with
White Stripe
Step 1. Step 2. Step 3.
IMPORTANT: Do NOT plug in the
adapter until after Step 4 is completed.
Connect power supply
wires to PROX-3 power
supply wires and negative
lead of the controller
Step 1 Cut off the barrel connector on the powersupply.
Step 2 Separate the wires.
Step 3
Connect the 12V adapter’s positive lead (solid black wire) to the red
wire on the PROX-3.
Step 4
Connect the 12V adapter’s negative lead (black with white stripe
wire) to the black wire on both the PROX-3 and the controller.
Step 5 Plug in the power supply.
Possible Cause Corrective Action
Incorrect wiring Verify wiring connection
Not enough power 12 VDC suggested
Mounted near electromagnetic interference Relocate or provide greater separation from
Incorrect card used Verify card compatibility from model number
Reader/access panel not properly grounded
Quality Earth Ground needed. Verify shield line from the access
panel to the reader is one continuous, connected line.
Supply generating electromagnetic interference Linear power supply recommended
Separate supply - no reference for data Connect BLACK from reader to BLACK of control system
(12 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals