Viking DEV1200 User Manual download pdf (Page 1)

READ AND SAVE THESE INSTRUCTIONS

MODEL DEV1200

EXTERIOR MOUNTED VENTILATOR

FOR USE WITH VIKING VCWH, VICH, DBCV, DICV, DCWH, DCWL, DCWN,

DTWS AND DCIH RANGE HOODS. 30" TO 66" WIDE, 9" TO 18" HIGH.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manu-

facturer. If you have questions, contact the manufac-

turer or your distributor.

2. Before servicing or cleaning unit, switch power off at

service panel and lock the service disconnecting means

to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a

tag, to the service panel.

3. Installation work and electrical wiring must be done by a

qualified person(s) in accordance with all applicable

codes and standards, including fire-rated construction

codes and standards.

4. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), and the American Soci-

ety for Heating, Refrigeration and Air Conditioning Engi-

neers (ASHRAE), and the local code authorities.

CAUTION

1. For general ventilating use only. Do not use to exhaust

hazardous or explosive material and vapors.

2. To avoid motor bearing damage and noisy and/or unbal-

anced impellers, keep drywall spray, construction dust, etc.

off power unit.

3. Please read specification label on product for further informa-

tion and requirements.

4. Electrical circuit, including speed control, (if used), must be

rated 6 AMPS minimum.

PLAN THE

INSTALLATION

1. Locate the ventilator so

the length of the duct run

and number of elbows

needed are kept to a mini-

mum.

2. Where possible, ventilator

should be centered be-

tween wall studs or roof

rafters.

3. Avoid pipes, wires, or other

ductwork that may be run-

ning through the wall.

ALL INSTALLATIONS

MODEL VOLTS AMPS CFM DUCT SIZE

DEV1200 120 3.0 1200 10" DIA.

SPECIFICATIONS

INSTALLER: Leave This Manual With The Homeowner

HOMEOWNER: Use And Care Information On Page 4

TYPICAL ROOF MOUNTED INSTALLATION TYPICAL WALL MOUNTED INSTALLATION

5. When cutting or drilling into wall, or ceiling, do not

damage electrical wiring or other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. To reduce risk of fire, use only metal ductwork.

8. This unit must be grounded.

WARNING

MODEL DEV1200

EXTERIOR VENTILATOR

10" ROUND

DUCT

SOFFIT

WALL HOOD

CANOPY

(island canopy available)

MODEL

DEV1200

EXTERIOR

VENTILATOR

10" ROUND DUCT

SOFFIT

10" ROUND ELBOW

WALL HOOD

CANOPY

(island canopy available)

Blower Dimensions

22 x 30.828 x 12.724

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - EXTERIOR MOUNTED VENTILATOR

READ AND SAVE THESE INSTRUCTIONSMODEL DEV1200EXTERIOR MOUNTED VENTILATORFOR USE WITH VIKING VCWH, VICH, DBCV, DICV, DCWH, DCWL, DCWN,DTWS AND DCIH RAN

Page 2 - LOCATION

11" dia.hole22"Guide hole(centered between studs)22"29½"29½"1411/16"1113/16"1113/16"17"Wall StudWall Stud

Page 3 - INSTALL THE VENTILATOR

1. Remove the cover and screws.2. Attach an appropriate U.L. approved cable connectorin the hole at the rear of the wiring box.3. Remove roofing nails

Page 4 - VIKING RANGE CORPORATION

GREENWHITEBLACKBLACKWHITEGREENBLACKWHITEGREENROUGH-IN PLATE LEADROUGH-IN PLATE LEADWIRING BOXEXTERIORVENTILATORBLACKBLACKBROWNCAPACITORWHITEBLUEBLACKG

Page 5 - MODÈLE DEV1200

VEUILLEZ LIRE CES DIRECTIVES ET LES CONSERVERMODÈLE DEV1200VENTILATEUR MONTÉ À L’EXTÉRIEURAVERTISSEMENTOBSERVEZ LES DIRECTIVES CI-DESSOUS DEMANIÈRE À

Page 6 - Roof Rafter

1. Choisissez un emplacement sur le mur extérieur. Assurez-vous qu’aucun poteau mural, tuyau ou câble ne passe auniveau de l’ouverture.2. De l’intérie

Page 7 - POSES SUR LES MURS

1. Retirez le couvercle et les vis.2. Fixez un connecteur de câble homologué U.L.dans l’ouvertureà l’arrière du boîtier de câblage.3. Retirez seulemen

Page 8

GREENWHITEBLACKBLACKWHITEGREENBLACKWHITEGREENROUGH-IN PLATE LEADROUGH-IN PLATE LEADWIRING BOXEXTERIORVENTILATORBLACKBLACKBROWNCAPACITORWHITEBLUEBLACKG