Viking K-1900-8 Specifications download pdf (Page 3)

B. Accessing the Programming Mode

1. Remote Programming

Step 1. Connect the green and red wires on the K-1900-8 to a C.O. line or analog PABX/KSU station.

Step 2. Set DIP switch 1 to ON.

Step 3. If using the multi-number dialer mode, set DIP switch 2 to ON.

Step 4. From a Touch Tone phone, call the line connected to the K-1900-8.

Step 5. Take the K-1900-8 off-hook (remove handset from cradle). A double beep should be heard indicating you have

entered programming.

Step 6. Program as shown in sections C - K.

Step 7. Set DIP switch 1 back to OFF.

Step 8. To exit programming, simply hang-up the phones.

2. Programming Without Using the Security Code

A. Security Code

A six digit number may be used to access the programming mode. The security code has been factory set to 845464 (V-I-K-I-N-G).

It is recommended that you change the security code to a personal 6 digit number as follows:

Step 1. Access programming as shown in section B.

Step 2. Enter your new security code followed by #47.

Step 3. To exit programming simply hang up the K-1900-8.

Note: The security code must be six digits in length and MUST NOT contain a

or #. If you have forgotten your security code,

see section “B, 2. Programming Without Using the Security Code.”

Step 1. If using the multi-number dialer mode, set DIP switch 2 to ON.

Step 2. Connect the green and red wires on the K-1900-8 to a C.O. line or analog PABX/KSU station.

Step 3. From a Touch Tone phone, call the line connected to the K-1900-8.

Step 4. Take the K-1900-8 off-hook (remove handset from the cradle) and enter “

,” followed by the six digit security code,

factory set to 845464 (see section A above). A double beep will indicate that programming has been entered.

Step 5. Program as shown in sections C - K.

Step 6. To exit programming, hang up both phones.

- then -

Speed dial number .................................................................................................................

Multi-number auto-dialer numbers 1-5 (DIP switch 2 must be ON) .........................................

, (anywhere in the speed dial number) .................................................................................

# (anywhere in the speed dial number) ..................................................................................

Set dialing speed to normal (Touch Tones: 120ms on/off, Pulse: 10 pps) (factory setting) .....

Set dialing speed to fast (Touch Tones: 50ms on/off, Pulse: 20 pps) ......................................

Block hand held pocket dialers (factory setting) ....................................................................

Allow hand held pocket dialers ..............................................................................................

Normal pre-dial pause (approximately 1.4 sec) (factory setting) ............................................

Short pre-dial pause (approximately 800 ms) ........................................................................

To add a one second pause at any point in the dialing string .................................................

To add a four second pause at any point in the dialing string .................................................

Toggle between Pulse and Touch Tone dialing (see section K) .............................................

Disable toll restriction (factory setting) ...................................................................................

Enable toll restriction .............................................................................................................

Change security code ............................................................................................................

To clear all phone numbers and return all programming to factory settings ...........................

1-32 digit (0-9)

1-16 digits (0-9)

6 digits (0-9)

###

# 00

#01 - #05

#47

C. Programming Features Quick Reference

Memory

Location

Enter Digits

Note: Special features such as a ,, a #, a mode change and a pause, use single digits in the programming memory.

D. Dialer Modes

The K-1900-8 can operate in 3 different modes. With DIP switch 2 set to OFF and memory location #00 cleared, the K-1900-8 is in

the Standard (Dumb) Phone mode. With DIP switch 2 set to OFF and a phone number programmed in memory location #00, the K-

1900-8 is in the Single Number Auto-Dialer mode. With DIP switch 2 set to ON, the K-1900-8 becomes a Multi-Number Auto Dialer.

E. Dialing Speed

To set the dialing speed, access the Programming mode as shown in section B, then choose a speed. To set the dialing speed to

Normal (Touch Tone: 120ms on/off, Pulse: 10pps), enter ,1. To set the dialing speed to Fast (Touch Tone: 60ms on/off, Pulse:

20pps), enter ,2.

1 2 3 4

Comments to this Manuals

No comments

Viking K-1900-8 Specifications Page 3

Comments to this Manuals

Related products and manuals for Security access control systems Viking K-1900-8