Viking Combination Beverage Center/Ice Maker Installation Guide download pdf (Page 3)

FULL OVERLAY PANEL INSTALLATION

Note: Weight of wood panel must not exceed 20 lbs.

Wood Screws

1. A #10 pan head wood screw should be used to properly secure the wood frame. A total of 10 screws will be needed

for a 3-1/2” (8.9 cm) kickplate or 8 screws for a 4” (10.2 cm) kickplate.

2. Only use pan head screws.

3. DO NOT select a screw that is longer than the wood thickness at

the screw locations.

4. Use recommended pilot holes for the frame material. (See chart)

Working Material Wood Screw Size #10

Hardwood 3/32 (0.24 cm)

Softwood 5/64 (0.20 cm)

Assembling Door Hinge Brackets

(Disregard if hinge brackets are already attached)

1. Attach the top and bottom door hinge brackets to the door with the #10-32 machine screws and a 1/8” allen head

driver as shown in Figure 1 below.

2. Press in the shoulder bushings to the top and bottom door hinge brackets. Make certain that the shoulder is to the

outside of the door as shown in Figure 1 below.

3. Test fit the door to the unit to make certain door will hang correctly. The door is hung correctly when the top of the

door is parallel to the top of the unit. (See Figure 2) Adjustments can be made by loosening the door hinge

machine screws and moving the door hinge brackets on the door.

4. Tighten all four (4) machine screws after adjustments have been made.

5. Remove the door from the unit by removing the units top hinge set screw and angling the door off of the bottom

hinge pin.

Figure 1

Shoulder Bushing

Door Hinge Bracket

#10-32 Machine

Screw

Door Hinge

Screw Holes

Door Front

Surface

Typical Top and Bottom

Door Hinge Bracket

Assembly

Figure 2

This surface parallel to the unit.

(Right hinge door shown

AREA REQUIREMENTS

Units Certified for Indoor Use - (black outer cabinet)

MUST BE INSTALLED IN AN AREA PROTECTED FROM THE ELEMENTS, SUCH AS WIND, RAIN, WATER (SPRAY OR

DRIP).

1. Place unit so the front side will be completely unobstructed to provide proper air flow. The unit may be closed in

on the top and three sides, but the front MUST BE unobstructed for air circulation and proper operation.

Installation should be such that the cabinet can be moved for servicing if necessary.

2. Unit should be in a well ventilated area. Best results are obtained at temperatures between 65°F (18°C) and 80°F

(27°C) for built-in products and 65°F (18°C) and 90°F (32°C) for freestanding products.

3. Provisions for electricity and water connection should be determined before placing unit in proper place.

Units Certified for Outdoor Use - outdoor models contain a T after the base model number (ex. VURI140T) and

have a stainless steel outer cabinet.

1. Place unit so the front side will be completely unobstructed to provide proper air flow. The unit may be closed in

on the top and three sides, but the front MUST BE unobstructed for air circulation and proper operation.

Installation should be such that the cabinet can be moved for servicing if necessary.

2. Unit should be in a well ventilated area with temperature above 45°F (7.2°C) and below 110°F (43°C). Best results

are obtained at temperatures between 60°F (16°C) and 100°F (38°C).

3. Provisions for electricity and water connection should be determined before placing unit in proper place.

4. For best performance, outdoor units should be installed away from direct sunlight or under a counter or shelter.

GENERAL INFORMATION

Unpack

1. Remove banding from bottom of carton. Lift carton up and off of the unit.

2. Remove all tape and packaging material from the outside and inside of the cabinet.

3. Keep all carton packaging until your unit has been thoroughly inspected and found to be in good condition.

LEG LEVELER INSTALLATION

Read Before Installing Leg Levelers

1. Four leveling legs are pre-installed in the base of the unit at the factory.

2. The unit should be leveled from front to back and side to side. If floor

conditions do not allow the unit to sit level, adjust the leg levelers by turning

the required leg leveler counter-clockwise to increase the height and clockwise

to reduce the height.

WARNING

Do not lay unit on top, side, back, or front. If unit is accidentally laid in

any position other than right side up, then the unit must remain in the

upright position for at least 24 hours before plugging the unit in.

1 2 3 4 5 6 7 8 9 10

Comments to this Manuals

No comments

Viking Combination Beverage Center/Ice Maker Installation Guide Page 3

Comments to this Manuals

Related products and manuals for Ice cube makers Viking Combination Beverage Center/Ice Maker