Viking C-1000B Specifications download pdf (Page 6)

3. Accessing the Programming Mode Locally (When ,5 mode has been programmed)

Enter

03 #01

12 #03

To Program the C-1000B...

1. ...to set door strike 1 to activate for 3 seconds

2. ...to set the auxiliary contacts to activate an external ringer or strobe light in a custom ring cadence while

either doorbox is ringing

3. ...to have doorboxes ring phones in a custom ring pattern

B. Quick Programming Features

Memory

Location

Enter Digits

- then -

Door strike 1 activation time .5 - 10 seconds (00 = .5 seconds/factory default) ....................

Door strike 2 activation time .5 - 10 seconds (00 = .5 seconds/factory default) ....................

Security Code (factory set to 845464) ....................................................................................

Disable special modes (,1 - ,6 and ,8) listed below (factory default) ...............................

* Doorbell mode .....................................................................................................................

* Custom ring mode ................................................................................................................

* Multiple relay activation mode .............................................................................................

* Paging mode (not for use with SLP-1, see Programming, Section F) ...............................

* Analog PABX/KSU station mode ..........................................................................................

* Inhibit latching commands mode .........................................................................................

Auxiliary contact mode (disables CCTV video control mode, factory default) .................

Auxiliary contact activation time .5 - 10 seconds (00 = .5 seconds/factory default)........

Auxiliary contact latched while either doorbox is activated .............................................

** Auxiliary contact activated in custom ring cadence ......................................................

**CCTV video control mode (disables auxiliary contact mode) .........................................

CCTV Inactive (Idle State) Modes:

Camera 1 and 2 output disconnected (factory default) ............................................

Output camera 1 ......................................................................................................

Continue to output video from last camera activated ..............................................

Sequenced video from camera 1 and 2 (rotates every 4 seconds) .........................

To reset to factory settings .....................................................................................................

* Note: Multiple modes may be selected.

** Note: Not compatible with Analog PABX/KSU Station mode.

#01

#02

#47

#03

#04

2 digits (00-10)

6 digits (0-9)

2 digits (00-10)

###

IMPORTANT: Only use Sections 3 or 4 when the C-1000B has previously been programmed into the “Analog

PBX/KSU Station Mode” (

Step 1. Connect a PBX/KSU analog extension (or phone line) to terminals 4 & 5, LINE OUT TO PHONES.

Step 2. Slide the TALK BATTERY switch to the OFF position.

Step 3. Move DIP switch 2 from OFF to ON (see Programming section E).

Step 4. Come off-hook with a phone connected to terminals 8 & 9 DOORBOX 1.

Step 5. PBX/KSU dial tone will be heard along with a double beep from the C-1000B to indicate that you have

accessed the programming mode.

Step 6. You can now Touch Tone program the features listed in section B below. (ignore busy signals, reorder tones or

intercept messages heard while programming).

Step 7. When finished programming, hang up and move DIP switch 2 to the OFF position.

4. Accessing the Programming Mode Remotely (When ,5 mode has been programmed)

Note: To access programming in this fashion, there must be a PBX/KSU analog extension (or phone line) connected to termi-

nals 4 & 5, LINE OUT TO PHONES and the TALK BATTERY switch must be set to OFF.

C. Programming Examples

Step 1. From another extension or phone line, call into the PBX/KSU analog extension (or phone line)

connected to terminals 4 & 5, LINE OUT TO PHONES.

Step 2. Answer the call using the phone (or device) connected to terminals 8 & 9, DOORBOX 1.

Step 3. From the remote phone enter , followed by the six digit security code (factory set to 845464, see

programming Section D).

Step 4. A double beep will indicate that you have accessed the programming mode.

Step 5. You can now Touch Tone program the features listed in section B below.

Step 6. When finished programming, hang up both phones.

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Viking C-1000B Specifications Page 6

Comments to this Manuals

Related products and manuals for Security access control systems Viking C-1000B