Viking FDW103 Installation Manual

InstallationVDW302 / VDW302WS RVDW103 / RVDW103WS FDW103 / FDW302FDW103WS/ FDW302WS CFDW103 / CFDW302Built-In Dishwashers

10Enclosure PreparationT20AB• Adjust the front foot level with theadjusting wrench to balance and raise thedishwasher to the enclosure height.• Adjust

11Installation PreparationAB• Check with your plumbing supply sourcesfor the proper hose and 90° elbow andnecessary fittings for the water supply line

12Installation PreparationABCThe dishwasher drain hose may be connected to the drain plumbing in one of three ways,(Figures A, B, C):Drain Preparation

13Installation PreparationSteam will form inside the dishwasher during operation. At the end of the cycle, when thedishwasher door is opened, it is re

14InstallationNow place the dishwasher into the opening and get ready to connect all hoses and electricalconnections.Note that the marks on therubber

15• Before pushing the dishwasher into thecabinet, you must place water supplyhoses into the channel of thedishwasher (Figure A).• Place the supplied

16Installation• After installing one clip for each side,push the dishwasher into the cabinet(Figure E).• Note that while pushingthe dishwasher into th

17Water supply may be connected to thedishwasher in one of two ways:• With metal braided hose.• With copper tubing.InstallationCAUTION• Hot water supp

18InstallationElectrical ConnectionWARNING• Make sure the voltage and frequencylisted on the data plate correspondwith the household electrical supply

19InstallationReadjusting Leveling LegsAdjusting the MovableKickplateNow that you have successfullyinstalled the dishwasher, youneed to attach the kic

Table of ContentsImportant Safety Instructions __________________________________________________________3Tools Which May Be Needed __________________

20InstallationIf the enclosure height is below 33-1/16”(84.0cm), use only (o) labeled kickplate(kickplate without slots). Installation shouldbe done f

21InstallationInstalling a Custom PanelMeasure the height and width of the enclosure(Figure A) and the kickplate. Determine how bigthe wooden door can

22Installation3. Mark the wooden door as shown in thedrawing (Figure C).4. Place the plastic mounting brackets over themarked holes. Align the bottom

23Installation5. Attach the two mounting brackets to thewooden door with 4 screws (Ø 1/8”x5/8”(Ø 3.55mmx14mm).6. Mount the wooden door onto the dishwa

24Installation11.Check whether the bottom ofthe door hits the kickplate ofthe kitchen cabinet (Figure A).11.1. If the door hits the kickplate, cut the

25InstallationSee also Page 21..NOTICEIf you have a European kitchen or want to install a wooden kickplate to match your kitchen,please refer to one o

26Installer Checklist and Final InstructionsYour installer must have completed andchecked the following:KThe dishwasher is square and level.KThe dishw

27Service & RegistrationOnly authorized replacement parts may be used in performing service on the appliance. Do notrepair or replace any part of

Viking Range, LLC111 Front StreetGreenwood, Mississippi 38930 USA(662) 455-1200For product information,call 1-888-845-4641or visit our web site in the

IMPORTANT3– Please Read and FollowSite PreparationIt is recommended that a thorough site inspection beconducted PRIOR to unpacking and moving this app

4• DO NOT operate the appliance if damaged, malfunctioning, partially disassembled, or if ithas missing or broken parts.• Also follow the safety instr

General Information5Tools Which May Be NeededPipe Wrench Wire Cutter DrillHole Saw Hammer Wire StripperTape Measure Torx Screwdriver(T20)Phillips Scre

6General InformationMaterials Which May Be NeededHot Water Supply Line – Minimum 3/8” O.D. copper tubing or metalbraided dishwasher supply line.90° el

7General InformationMaterials Suppliedx1x1y.x4x2x2a.b.d.e.f.g.h.c.j.k.l.o.p.s.v.n.r.t.m.x1x1x1x1x6x1x1x1x1x1x1x4x2x2x1z.x1Dishwasher Parts Bag 1This d

8Specifications24” max(61.0 cm max)24” max(61.0 cm max)24” max(61.0 cm max)Built-In DishwasherOverall WidthOverall Height from FloorOverall Depth from

9Electrical PreparationPreparation for Installing Mounting BracketsEnclosure PreparationWARNINGThe dishwasher is designed for an electrical supply of